When I think of #Winter here, I just think of the cold, the rain, and all of the times I was either borderline or actually hypothermic when #cycling and similar outdoor activities in it. :blobfoxsad:
In all my years of #cycling, I've never found a great solution for cold weather. If I bundle up so I'm not chilled, then I soak everything with sweat in short order. If I wear less, then I freeze. I've tried Merino wool, synthetics (Gore, Event, etc.), and so on, but nothing works well enough for me.
Sadly, that means I don't do anything exciting on the #bicycle during the coldest part of the year. Just my daily local loop. :blobfoxsad:
@tk@biketooter@cycling@mastobikes I find I have a crazy steep temp gradient with almost any aerobic exercise and chronically overdress, so this makes sense to me
@tk@biketooter@cycling@mastobikes i warm the absolute hell out of my hands and feet before going out but for bicycling especially it’s been awhile. Want access to a mountain bike with nice wide tyres for actual snow.
innicycle’s unique system combines a threadless stem adapter with a sealed cartridge bearing headset. The result: Finally a way to tastefully incorporate modern components with your vintage bicycle.
Advantages
Lower weight & greater rigidity
Retains stock threaded fork
Compatible with modern handlebars and stems
Easily adjusted bearing preload using only a 6mm hex key
Ultra low stack height (low stem position adjust-ability)
Fitment
The innicycle Threadless Conversion Headset™ is compatible with most road and some MTB bikes that originally came equipped with 1” threaded headsets and quill stems. Forks must be 1”-24 TPI threaded with a 7/8” (22.2mm) inside diameter. Both ISO and JIS* fork crowns are supported.
If I were to get a titanium #bicycle, I'd definitely spec a compliant steel fork. I feel like steel folks get a bad rap because consumer grade production ones are overbuilt, especially ones with disc brakes! #cycling
I have an aluminum frame track bike with a carbon fork that I am considering switching to a steel fork. I guess the ride a little whippier but the front wheel is the place you want rigid control over what is moving where...
“I’m thinking about getting longer cranks”, said no one in 2023. It’s definitely true that shorter cranks are a trend right now, but why? Is it all nonsense, or is there something to it? Today we’ll take a deep dive into crank length and how it affects your performance. You’ll get a highly biased take on the subject from someone with very short legs.
Considering handlebar covers/mittens for doing #OpenStreetMap updates in cold weather. They're quite pricey though. Would they help?
It's fairly slow travel, with frequent stops near the footway=sidewalk to record data on the phone. Are they any good for that sort of thing, if I use them with a pair of insulated fingerless gloves underneath? #BikeTooter@bikes@mastobikes@cycling
I still like rim brakes, but I don't have any major opposition to disc brakes as long as they're using with thru-axles. (I don't like the pads rubbing after hard braking, which is usually caused by the hubs shifting.)
Finally figured out the process for getting my correct saddle position on a bike!
Start with the saddle level, a bit low, and slammed all the way back on the rails.
Raise the saddle in 3-5mm increments until you no longer lift off the saddle or have pain on or around your kneecaps. You may need to move the saddle forward a 3-5mm every now and then so you aren’t completely sitting on its nose.
Once #2 has been taken care of, pedal with the technique of spinning your knees in small, tight, and fast circles. That pedaling technique will cause you to scoot forward to where your saddle should be.
Move the saddle forward in 3-5mm increments until it feels comfortable with that pedaling technique. Be sure to keep the saddle as level as possible while doing this.
Coming from The Netherlands the Danish cycling infrastructure -and value society gives to it- has a lot of room for important.
That said, at least it's not France where they put a #christmas tree right in the middle of a cycle lane as that's easier than getting a two meter extension cord for the lights..